Back to shop ↗
THE HOLDEN COMMODORE FORUM

HOLDCOM Community

Built around the cars. Kept alive by the people.

+ Start a discussion
Holden Commodores gathered at Holdcom
Forum Home›General discussion
General discussion

post VB-VK pics here!

Started by Calais_Nv · 2 July 2006 · 434 replies

Preserved from CalaisTurbo (partial recovery). Original authors and dates are shown; archived members are not current Holdcom accounts.

[FLY-BYE]Archived member
heres mine Some original photos have not been recovered yet.
Photo 1 shared by [FLY-BYE]Photo 2 shared by [FLY-BYE]
0 likes
hiy_poArchived member
This is my VK Turbo 5 speed. No show stopper but built on a real tight budget. Has Rajay turbo rated 650HP and Mike Vine 400hp twin carb setup. I have EFI ready to bolt on when Im ready to mess with it again. Am looking for somewhere in Perth that will fit my Wolf3D ver4.4 for a bit less than the $800 Im getting quoted at the moment. Has the original EST sender units and computer still installed but disconnected at coil and using HEI dissy is 350rwhp in present trim but pings abit in 3rd and 4th under full boost. This is the 3rd time Ive tried to post if all 3 suddenly turn up oooops sorry bout that. Some original photos have not been recovered yet.
0 likes
Calais_NvArchived member
cool sleeper , do you plan on going all out with it? interior , paint etc
0 likes
hiy_poArchived member
Quote: Originally Posted by Calais_Nv cool sleeper , do you plan on going all out with it? interior , paint etc No itll get EFI but is used on too regular basis to spend any time off the road. The bonet is a 2 can spray pack job that took me couple of hours Had my first good work out today against a HSV r8 clubsport he got the jump on me coz we were both turning right at the lights but by third I was half a car ahead Some original photos have not been recovered yet.
0 likes
Calais_NvArchived member
pretty cool thats its actualy daily driven! guy in the r8 must have been spewin lol
0 likes
GMH050Archived member
HERE YA GO HAVE A LOOK AT MY VK BT1 INJECTED 5LTR WITH BIG CROW CAM Some original photos have not been recovered yet.
0 likes
stuffArchived member
Heres my ride.
Photo 1 shared by stuff
0 likes
NZ EVLHSVArchived member
NZ styles...
Photo 1 shared by NZ EVLHSVPhoto 2 shared by NZ EVLHSVPhoto 3 shared by NZ EVLHSVPhoto 4 shared by NZ EVLHSVPhoto 5 shared by NZ EVLHSVPhoto 6 shared by NZ EVLHSV
0 likes
Calais_NvArchived member
good pics tuff hdt speaks for itself
0 likes
vlturbz12Archived member
my old vh v6 slx wagon
Photo 1 shared by vlturbz12Photo 2 shared by vlturbz12
0 likes
dvsgmhArchived member
^^^^^^^^^^^^^^^swap you my bt1?
0 likes
vkboyArchived member
heres my new vk calais, got it afew weeks ago, 308 manual. during the week the engine decided to pack it in, so iv pulled it out today n will be rebuilding it over the next few weeks, will be my daily driver but that doesn't mean i can't build a tough little motor. has a 4 speed in it atm but ditching it for a supra box as ive got a spare one hanging around, which should b abit nicer. here it is atm with no engine and just chucked some polished calais wheels on it earlier, i love em. Some original photos have not been recovered yet.
0 likes
KORUPTArchived member
looks tuff sim
0 likes
Wkd_VlArchived member
looks nice dude. must be pissed that the motor packed up after you just bought it
0 likes
FAQFPVArchived member
Some original photos have not been recovered yet.
0 likes
ISK8BYArchived member
VKBOY- those vk calais wheels look mad as!! and that is one of the best looking wagons ive seeen good job ONA-747
0 likes
Calais_NvArchived member
black over silver vk looks hot mate keep us informed! ona 747 that has to be only wagon i can honestly say i like very nice
0 likes
vkboyArchived member
thanks for the comments guys, if i get around 200rwkw out of this motor i'll be happy, heres afew bits im chucking in: crane 286 cam crane antipumpup lifters edelbrock performer manifold acl flat tops and bearings a9l rods l34 valves 40 thou over modded quadrajet etc its got an lsd borgie diff in it alread which will do the job, but he gearing is too tall at 3.36:1, so wouldn't mind changing to 3.7:1. taking the engine to work tommorow to start stripping it down, bit of fun . Some original photos have not been recovered yet.
0 likes
ONFLYTArchived member
heres my mates car Some original photos have not been recovered yet.
0 likes
chasdmArchived member
Here's a mates Some original photos have not been recovered yet.
0 likes
Sign in or create an account to reply. New members are welcome—no purchase or old CT account needed.

Who’s online

0 members and 0 guests active in the last 15 minutes

No signed-in members active right now. Guests are welcome to browse.

Visitors Today20

33,602 threads, 484,230 posts and 24,897 images saved from CalaisTurbo.
As at . Recovery is continuing.