can they be just wired up to standard plug that used to plug into the normal single fan setup? without the thermo fan kit thingo?

GMH05- no.

I find an easy way of controling these fans is with a KC KE laser thermo fan switch. This type of sensor is loses its ground when it reaches temp, so you have to use a 5 pin relay to switch your 2 4 pin fan relays on. So essential u r using a low voltage circuit to turn on a high voltage circuit. If you tap the sensor in where the vl coolant bleed is this puts the sensor right in the path of hot water. fans cut in and and out at about 90c. heaps neater than temp probes that clamp into top hoses. hope that helps a few people

^^^^ what rapidflow said - spot on. tridon make a heap of sensors to do this, all here : 100% full credit to CrUZida from www.toymods.net (http://www.toymods.net) forums for this info. Some original photos have not been recovered yet.

Ooooh, that's very cool. Good find! If the probe turns out to be messy, then I'll go this path. Only advantage of the probe is that it's fully adjustable.

probe is adjustable, yes. remember, if you're running a stock ECU the maps ect are expecting the engine temp to be within a certain range - if you run the engine colder you may get differing results... only issues i've had with the probe is when using organic (orgasmic) coolants they tend to grow fur around them Some original photos have not been recovered yet.

Quote: Originally Posted by 7FOUR7 I have a brand new set of AU twin thermos still in the box that I'm selling if anyones interested. bump that **** nooka

Quote: Originally Posted by Grega probe is adjustable, yes. remember, if you're running a stock ECU the maps ect are expecting the engine temp to be within a certain range - if you run the engine colder you may get differing results... only issues i've had with the probe is when using organic (orgasmic) coolants they tend to grow fur around them No stock ECU here boss. Some original photos have not been recovered yet.

i just installed mine fits really good i think i will get some pics up its in a vs stato. Wiring not done yet.

has anyone got these thermo's and a gktech cooler kit????? wanting to know if the pipes miss the thermo or ill have to go back to a clutch fan im currently using a 16inch davies craig fan and its not up to the task on hot hot days. cheers

Quote: Originally Posted by 7FOUR7 bump that **** nooka how much you want for them?

Quote: Originally Posted by vlwagz has anyone got these thermo's and a gktech cooler kit????? wanting to know if the pipes miss the thermo or ill have to go back to a clutch fan im currently using a 16inch davies craig fan and its not up to the task on hot hot days. cheers I'm sure there's someone running it.

Also wanted to know if anyones running the twin thermo fans with the gktech IC piping? Im looking at doing this mod but want to make sure b4 going ahead with it... cheers

If you have a look at how big the fans are, and where the cooler pipes run it seems like it would be very difficult. I am jsut going to get a single craig davies fan and hook it up to a switch inside the car. Also will be getting a slim aircon fan.

will be getting a single thermo fan today, but l will be trying to install it in the original clutch fan shroud, would that be any good? twin au or el fans wont fit unelss l modify the gktech cooler pipes.

i have a single thermo and i have to have it running all the time.

so you don't have it switched on when it reaches a certain temperature? Did you install a shroud? It would be pretty useless l would think if it doesn't have a proper shroud.

craig davies? craig david? old school singer guy? better off with something that has a proper shroud cos a single thermo wont pull air thru the whole rad while one with a shroud will..

Putting one of these on my project. After dummy fitting it today i realised i needed to remove the two teets from the radiator. Do i need to buy a transmission cooler to plug the trans lines into so it cools? Its an NA vl for now with turbo coming.

Addvice Dont Do This Mod Its Not Even Worth The Trouble i have converted Mine Now Wish i Didnt !