Welcome to GRUNT PERFORMANCE! After months of waiting we are finally here to give you all the top quality products for your engines i will be specialising in Nissan RB30 products, but will have everything soon for your car (will provide a list of products soon), ALL PRICES ARE PLUS POSTAGE UNLESS LISTED OTHERWISE Custom oversized RB30 valves are now an off the shelf item from GRUNT PERFORMANCE, These are made from the highest grade one piece high nickel content 21-4N stainless steel, All valve stems coated in black nitride to minimize valve stem wear. will provide pictures asap for you all. Valves SINGLE PIECE VALVES RB30+1mm inlet valves STAINLESS SINGLE PIECE 21-4N $200 per set COMING SOON RB30+1mm exhaust valves STAINLESS SINGLE PIECE 21-4N $200 per set COMING SOON RB30+2mm inlet valves STAINLESS SINGLE PIECE 21-4N $210 per set COMING SOON RB30+2mm exhaust valves STAINLESS SINGLE PIECE 21-4N $210 per set COMING SOON RB30+3mm exhaust valves STAINLESS SINGLE PIECE 21-4N $220 per set COMING SOON 2 PIECE VALVES RB30+1mm inlet valves black nitride coated $50 PER SET IN STOCK RB30+1mm exhaust valves STAINLESS 21-4N black nitride coated $50 PER SET IN STOCK RB30+2mm inlet valves black nitride coated $50 PER SET IN STOCK RB30+2mm exhaust valves STAINLESS 21-4N black nitride coated $50 PER SET IN STOCK RB30+3mm exhaust valves STAINLESS 21-4N black nitride coated $50 PER SET IN STOCK I am currently looking into RB25/26 valves also so they should be here shortly RB30 H-Beam/I-Beam - Tell me what engine you have and i will get H-Beam 4340 grade rods for it for only $85 per rod.... i have over 750 different engine types that i can have these rods made to... if i dont have them in stock i will order them. - Custom rods can be made for any engine for only $120 per rod as long as you provide the specs. All these prices are with out rod bolts H-Beam Billet steel 4340 grade -$500 per set with out bolts - $650 per set with ARP2000 bolts Weight - 510 grams Big end - 53mm Big end width - 21.8mm Small end - 21mm Small end width - 21.8mm Centre to centre - 152.5mm Matched weight - +-1.0grams 1> Connecting rod Material: 40CrNiMoA(4340) Forged Steel. 2> Hardness after quenching and tempering is HRC33-38. 3> Special Dowelled cap for alignment 4> X-RAY & Sonic tested 5> Silicon bronze bushings 6> Fully machined to produce the lightest and strongest rod possible 7> Shot peened 8> 100% Magnafluxed I-Beam billet steel 4340 grade - coming soon -$500 per set with out bolts - $650 per set with ARP2000 bolts Weight - 510 grams Big end - 53mm Big end width - 21.8mm Small end - 21mm Small end width - 21.8mm Centre to centre - 152.5mm Matched weight - +-1.0grams 1> Connecting rod Material: 40CrNiMoA(4340) Forged Steel. 2> Hardness after quenching and tempering is HRC33-38. 3> Special Dowelled cap for alignment 4> X-RAY & Sonic tested 5> Silicon bronze bushings 6> Fully machined to produce the lightest and strongest rod possible 7> Shot peened 8> 100% Magnafluxed I-Beam titanium grade 5 - coming soon - $2000 per set with out bolt I-Beam billet Aluminium grade - $700 per set with out bolt - $850 per set with ARP2000 bolts Weight - 324 grams Big end - 53mm Big end width - 21.8mm Small end - 21mm Small end width - 21.8mm Centre to centre - 152.5mm Matched weight - -+1.0grams 044 PUMPS FOR 700-800 HP APPLICATIONS 300lph rate at 3 bar fuel pressure (43.5psi) 200LPH @ 72.5psi (5 bar) INLET CONNECTION: M18X1.5 OUTLET CONNECTION: M12X1.5 LENGTH: 196 mm DIAMETER: 60 mm MAX POWER/Cons(Amps): 15.5 come with 6 months warrentee - $80 express delivered anywhere in australia. 2 x 044 pumps - $140 express deliver anywhere in australia FUEL FILTERS Washable filters -6an - $40 each Washable filters -8an - $45 each TURBO OIL LINE FILTER -4an - $20 each -6an - $20 each SURGE TANKS 2.5ltr 2 x -8an Outlet 3 x -6an feeds - $135 each 2.5ltr 1 x -8an Outlet 3 x -6an feeds - $120 each EXHAUST WRAP Ceramic wrap 50mm x 2mm x 10mtrs 1200deg - $30 each TURBO BEANIE T3 - $90 each T4 - $100 each PUMP BRACKETS ANIDIZED RED/SILVER/BLUE - $20 each 1700cc injectors only $100 each DELIVERED (EXPRESS) rb30 rail suit 14mm injectors $200 DELIVERED (EXPRESS) RED/BLUE/CHROME RB30 RAIL with 6 x 1700CC injectors ONLY $699 DELIVERED (EXPRESS) Static Flow Rate: 152lb/hr = 9.42g/s = 1680 cc/min (+/-4%) Dynamic Flow Rate 2.5ms PW @ 100Hz: 16.9 mg/pulse (+/-4%) Coil Resistance: 2.35 Ohms / Low Impedance / Low-Z (Peak/Hold driver circuit required) Connector: Minitimer (Bosch EV1) Factory fitted with Viton upper and lower o-rings. These injectors flow 1600 cc/min at 43.5 PSI ( 3 BAR ) and are fully compatible with alternate fuels and alcohol! Some websites may refer to their flow rating as 160 lb/hr or 150 lb/hr or 1680 cc/min Bosch Low Impedance Injectors. Frequently used in racing, flex fuel applications and alternate fuel applications, these low impedance injectors combine extremely high flow rates with excellent response at low pulse widths! This allows you to use a larger injector than normally possible without hurting idle and low speed drivability. These injectors are able to function at high fuel pressures and don�t exhibit the high fuel pressure handling problems found with many other high flow high-impedance injectors. This makes these injectors very well suited to turbocharged and supercharged applications that see high fuel system pressures. RB30 arp head stud kits = $284 RB30 arp main stud kits = $220 RB30 cometic head gaskets = $264 RB30 king big end bearings = $55 RB30 king main bearings = $130 RB30 powerbond 25% underdriven balancer = $250 RB30 vernier adjustable cam gear = $280 RB30 heavy duty auto flexplate = $345 RB30 dual valve springs .470"-.480" lift / 90 pound on seat / 220pound @ 10mm lift = $100 RB30 dual valve springs with retainers .600" lift / 120 pound on seat / 250 pound @ 10mm lift = $180 FUEL SYSTEM PACKAGES TWIN SETUP 1 x 2.5ltr twin outlet 2 x 044 pumps 2 x -6/-8an washable filters 2 x pump brackets $400 express delivered anywhere in AUS SINGLE SETUP 1 x 2.5ltr single outlet 1 x 044 pumps 1 x -6/-8an washable filter 1 x pump brackets $260 Express delivered any where in AUS NOW A DEALER OF TURBOSMARTS GEAR! PM ME FOR PRICES, COMPLETE RANGE AVAILIBLE Some original photos have not been recovered yet.

great! will be keeping an eye on this thread!! do u do plenums and exhaust manifolds?

great to see ur up and running kirk, gd luck with it all bud!

Quote: Originally Posted by FRKVLT [View Post] great! will be keeping an eye on this thread!! do u do plenums and exhaust manifolds? i can get them but not custom ones as i havent gone down that track as i will leave the exhaust manifolds to 6boost and plenums to isleep

Welcome mate, bout time :p I look forward to seeing what you bring to the market ;) You might even get me interested in building another RB30.

We need clear timing belt covers.

yeah i agree, i am getting stuffed around with the postage company atm, as the sample hasnt even been delivered to the supplier... and there tracking number doesnt seem to come up on there system. but i will let you know you as soon as i do, as there is alot of interests in them

With the rods will you be offering different pin sizes? Rod and piston combos? Hp rating? Good luck mate, good to see some different parts been offered for the vls

i can get larger 22mm pin sizes but i am holding off at the moment to see how all these go first. Been looking into combos for pistons and rods as i can get forged and billet pistons for rb30's but am holding of on that also at the moment. The 4340 rods have been over 1000rwhp and the aluminium will hold more again... i will be making threads soon of some of my test cars for my products so you can all be updated and can see what they can really do.

What sort of sizing would you recommend for an rb25 head?

how long till u got all your pics and prices up ?

Quote: Originally Posted by jbonez [View Post] What sort of sizing would you recommend for an rb25 head? Still looking into it at the moment but will pm you and let you know how the are going ---------- Post added 07-07-11 at 21:52 ---------- Quote: Originally Posted by bibbz [View Post] how long till u got all your pics and prices up ? The rods you see are my rods with out my logo on them, the valves are currently getting made but should have pic up soon of them with the logo and all... As for pricing of the rods will have that up this week, just waiting on the price of the rod bolts... What are you exactly interested in?

i was going to buy some h beam rods off ebay they sell them for 700 but i wanted to see how much u would charge

Im interested in those clear cam covers, can ya PM me when you know the price or have any pics? cheers

yeh clear cams covers for the win

yes i really want the cam covers also but the sample for the mold that was sent to the supplier seems to have not turned up and cant get hold of the sender. so i might have to find another cam cover to send to the molder... If you know anyone that has one and wants to sell one let me know please guys. sick of getting stuffed around by this bloke

I'd be interested in a clear cam cover are they for rb30et how much will they be

the price will all depend on how much the mold is, but i will let you know as soon possible. Also rods prices are up guys....

rods are cheap thats for sure

Quote: Originally Posted by EVLRB30 [View Post] rods are cheap thats for sure buy a set then haha, people should take advantage of it as im trying to get the name out there....