Preserved from CalaisTurbo. Original authors and dates are shown; archived members are not current Holdcom accounts. View original archive ↗
I need help, I have a Nizpro Intercooler, standard turbo, standard computer and 15 pound boost
I'm getting new pistons and while the motor out Im looking for a camshaft. Later I want a ballbearing turbo and aftermarket computer
Ive heard about a stage 3 camshaft by AVO can any one help with any suggestions
0 likes
pm lukevl.
he works at a cam shop and is very helpful to talk to
0 likes
jpc makes the best cam packages i think its a crow cam and works well there are 2 stages good luck
0 likes
Quote:
Originally Posted by duz360
pm lukevl.
he works at a cam shop and is very helpful to talk to
How do i contact him?
0 likes
Goto your PM box and send a PM to lukevl
Some original photos have not been recovered yet.
0 likes
http://www.rocketindustries.com.au/
go to crow cams
0 likes
Yeah I have a crow 221 cam... I got it through JPC, but I didn't know it was a crow cam until I got it... prolly could have gotten it cheaper direct from crow, but oh well...
They told me that it was the same cam that they use in their drag VLT...
I found that it really comes on well at about 3000rpm, or when at full boost.... made the engine more responsive all though the rev range...
0 likes
i had a jpc/crow stage 1, and then went to one of lukes cams. let me say it is definately more aggressive but luke can grind you a cam to suit what ever application you have in mind, just pm him, he is very helpful. i'm pretty sure he is cheaper than crow, and definately cheaper than JPC.
regards
mark
Some original photos have not been recovered yet.
0 likes
The Crow/JPC stage 1 will work well with standard computer. It is a good performance street cam, its a good cam for a street/strip car. There stage 2 is a good cam will run a fairly easy 10 (not sure if they are good for a 9). http://www.crowcams.com.au/template...Commodore.shtml (http://www.crowcams.com.au/templates/Catalogue-TurboVLCommodore.shtml)
However if your going a stage 2 JPC or AVO stage 3 I recommend going aftermarket ECU and injectors first. From what I know you will have a hard time getting your motor to run properly with these cams using the standard ECU.
0 likes
08-08-04, 19:29 GMT+10#10 whats ppls opinions on the Wade 818b (i think) cam?
0 likes
11-08-04, 02:49 GMT+10#11 Quote:
Originally Posted by GMH-GEM
whats ppls opinions on the Wade 818b (i think) cam?
That's what i got in mine(wade 818b)
I think it's pretty good actually, comes on about 3ish,pulls hard all the way to 7200rpm.
used to have the JPC stage1, went to the wade 818b.Most of Rajabs cars and bresciani's cars use them, so i'm told.Good for 10's.
PSI.
0 likes
11-08-04, 10:47 GMT+10#12 what about the jpc/crow stage 2? any good?
0 likes
11-08-04, 11:09 GMT+10#13 i didnt know u had a stage 1 cam craig? how much did it cost you and how much did it cost you to install?
0 likes
11-08-04, 17:00 GMT+10#14 Quote:
Originally Posted by Bill
what about the jpc/crow stage 2? any good?
stage 2 likes to rev, loose a bit down low but she comes on boost nice and hard
not really necessary i dont think, stage 1 is enough for a street car
0 likes
11-08-04, 18:00 GMT+10#15 Whats a decent cam to get for a N/A stock engine? And how much would it cost?
0 likes
12-08-04, 13:18 GMT+10#16 the standard one, keep as much low end torque as you can
0 likes
